设计简介
摘要 此次设计为简单的单工序模，工序只有一道，落料。是冲压模具的基本形式。设计选用最普通的压力机，使用简单的定位件，尽量选用标准件。模具零件材料则大多取用常用材料，以减少成本。该模具易于制造，可在普通冲床上使用，适合在生产中推广应用。
Workpiece punching
ABSTRACT This design is just a simple work procedure die.There are only one work procedure.This design choices the proximal simple punch,uses the simple accessory for going to mould,and choices standard accessory to the best . In the interest of reducing cost,Most materials of mould accessory are choicing the usual material .This mould is easy to produce.It can used on the usual punch,and adapt to generalize in producing.
盖板落料冲压模具设计（正装）
目录
摘要............................................... ..... ........（1）
ABSTRACT.......................................... ..... .........（1）
第一章 绪论与概述................................ ..... ...........（2）
1.1国内外模具发展现状及前景....... ..... .......................（2）
1.2模具工艺发展过程及发展方向........... ..... .................(3）
第二章 冲裁理论与主要计算.................. ..... .................(4)
2.1冷冲压概念...........................................(4)
2.2模具方案论证.........................................(5)
2.2.1工艺计算...........................................(6)
2.2.2凸模和凹模工作部分尺寸的计算.......................(8)
2.2.3凹模的外形尺寸确定................................(10)
2.2.4 凸模固定板的确定.................................(11)
2.2.5凸模的外形尺寸确定................................(11)
2.2.6 导料板的确定.....................................(12)
2.2.7卸料装置的确定....................................(12)
2.2.8 模柄的选用.......................................(12)
2.2.9冲模闭合高度计算.................................(12)
2.2.10压力机的选择....................................(12)
第三章 模具设计.................................... .........(12)
3.1凹模结构............................................(12)
3.2凸模结构—................................. ........(13)
3.3凸模固定板结构......................................(13)
3.3.1卸料板的结构......................................(14)
3.3.2导料板的结构......................................(14)
3.3.3垫板的结构........................................(14)
3.3.4模架..............................................(16)
3.3.5模柄的结构.......................................(19)
3.3.6卸料螺钉的结构...................................(19)
3.3.7固定挡料销的结构.................................(19)
3.3.8 圆柱销的结.......................................(20)
3.3.9 弹簧结构.........................................(20)
第四章 模具的加工......................................(21)
4.1 凸模的加工.........................................(22)
4.2 凹模的加工.........................................(22)
4.3 垫板、凸模固定板、卸料板...................... .........(22)
设计总结
致谢
参考资料
Workpiece punching
ABSTRACT This design is just a simple work procedure die.There are only one work procedure.This design choices the proximal simple punch,uses the simple accessory for going to mould,and choices standard accessory to the best . In the interest of reducing cost,Most materials of mould accessory are choicing the usual material .This mould is easy to produce.It can used on the usual punch,and adapt to generalize in producing.
盖板落料冲压模具设计（正装）
目录
摘要............................................... ..... ........（1）
ABSTRACT.......................................... ..... .........（1）
第一章 绪论与概述................................ ..... ...........（2）
1.1国内外模具发展现状及前景....... ..... .......................（2）
1.2模具工艺发展过程及发展方向........... ..... .................(3）
第二章 冲裁理论与主要计算.................. ..... .................(4)
2.1冷冲压概念...........................................(4)
2.2模具方案论证.........................................(5)
2.2.1工艺计算...........................................(6)
2.2.2凸模和凹模工作部分尺寸的计算.......................(8)
2.2.3凹模的外形尺寸确定................................(10)
2.2.4 凸模固定板的确定.................................(11)
2.2.5凸模的外形尺寸确定................................(11)
2.2.6 导料板的确定.....................................(12)
2.2.7卸料装置的确定....................................(12)
2.2.8 模柄的选用.......................................(12)
2.2.9冲模闭合高度计算.................................(12)
2.2.10压力机的选择....................................(12)
第三章 模具设计.................................... .........(12)
3.1凹模结构............................................(12)
3.2凸模结构—................................. ........(13)
3.3凸模固定板结构......................................(13)
3.3.1卸料板的结构......................................(14)
3.3.2导料板的结构......................................(14)
3.3.3垫板的结构........................................(14)
3.3.4模架..............................................(16)
3.3.5模柄的结构.......................................(19)
3.3.6卸料螺钉的结构...................................(19)
3.3.7固定挡料销的结构.................................(19)
3.3.8 圆柱销的结.......................................(20)
3.3.9 弹簧结构.........................................(20)
第四章 模具的加工......................................(21)
4.1 凸模的加工.........................................(22)
4.2 凹模的加工.........................................(22)
4.3 垫板、凸模固定板、卸料板...................... .........(22)
设计总结
致谢
参考资料
