您好,欢迎来到机械CAD网!
客服QQ:20425042

首页 > 机械机电 >

设计名称
番茄打浆机设计【红薯等打浆机】【说明书+CAD】
设计编号
JX3885
设计软件
AutoCAD,Word
包含内容
见右侧图片
说明字数
见下方截图
图纸数量
见右侧图片
推荐指数
较高
价格
价格优惠中
整理日期
2017-09-23
整理人
admin
设计简介
番茄打浆机设计
摘    要
在食品生产中,并不是把所有的原料全部加工成最终产品,在加工时必须去掉不合适加工的部分。在生产工艺过程中,也要根据具体的感官、理化指标的不同要求,对其半成品中的某些组成部分予以分离。分离中不和缺少破碎桨叶和螺旋推进器。
番茄打浆机适用于多种新鲜的果品和蔬菜打浆分离之用,随着人们生活水平的提高,西红柿打浆机在人们的生活中扮演的角色越来越重要。对于打浆机,在工程设计及使用中还存在一些的缺陷,如参数选择不合理等。目前,打浆机的设计仍是依靠经验公式计算,在经验公式中许多参数的选择是在一定范围内凭经验选取,这使的打浆机的设计较落后,无法提高其设计水平和提高产品的性能。
关键词:打浆机;破碎桨叶;螺旋推进器;电动机;番茄浆液
ABSTRACT
In food production, not all of the raw materials are all processed into the final product, inappropriate processing of the part must be removed during processing. In the production process, but also depending on the sensory, physical and chemical indicators of the different requirements of certain components in the semi-finished products to be separation. Separation and the lack of broken blade and propeller.
Tomato beater for a variety of fresh fruits and vegetables beating isolated, tomatoes beater in people's lives play an increasingly important role, along with the improvement of living standards. Beater, engineering design and use, there are still some defects, such as parameter selection, such as irrational. The design of the beater still rely on empirical formulas, the choice of many parameters in the empirical formula empirically selected within a certain range, which makes the design of the beater backward, unable to raise design standards and improve product performance .
Key word: beater; broken blade; propeller; motor; tomato slurry
目    录
摘要 I
Abstract II
第1章 绪论 1
1.1本课题的来源、基本前条件和技术要求 1
1.2研究成果研究番茄打浆机目的和国内外现状概况 1
1.3番茄原料加工预处理工艺流程简介 3
1.4国内外番茄打浆设备 4
1.5本章小结 5
第2章 打浆机的结构设计 6
2.1 基本结构设计 6
2.1.1 圆筒设计 6
2.1.2 破碎桨叶设计 6
2.1.3 传动部分 6
2.1.4 机架 7
2.1.5 其他 7
2.2 本章小结 7
第3章 打浆机设计参数的确定 8
3.1 滚筒的设计 8
3.1.1 滚筒长度 8
3.1.2 物料在滚筒内的时间 8
3.1.3 棍棒与筛筒之间的间隙 9
3.1.4 圆筒筛消耗功率的计算 9
3.2 电动机的选择 10
3.3 本章小结 10
第4章 主要零件的结构设计与计算 11
4.1 皮带轮的设计与计算 11
4.2 传动主轴的结构设计与计算 14
4.2.1 初步计算轴的直径 14
4.2.2 轴的结构设计 15
4.3 轴上零件的定位 15
4.4 确定轴上的圆角和倒角 15
4.5 轴承的选取 16
4.6 本章小结 16
第5章 主要零件的校核 17
5.1 轴的强度校核计算 17
5.1.1按扭转强度条件计算 17
5.1.2按弯扭合成强度条件计算 18
5.2轴的扭转刚度校核计算 19
5.3 轴承寿命的校核 19
5.3.1   30211轴承 19
5.3.2   30212轴承 20
5.4 键的校核 20
5.5 本章小结 20
结论 22
参考文献 23
致谢 24
部分图纸截图
展开
  • 在线咨询
  • QQ:20425042
  • QQ:99872184
  • 技术支持
  • 售后服务