设计简介
首先，本文介绍了模具的发展和现状以及模具在现实生活中的广泛应用。其次，文章详细的对竖笛尾段进行了注射模的分析和设计。
设计中介绍了成型机中各个零件的选择。着重阐述了注射模具浇注系统的设计；注射模具分型面的选择；注射模具侧抽芯机构的设计等。
对零件型腔的设计采用了哈夫分型，侧抽芯机构并做到一模两腔。还对型腔进行了严格的计算。
文中还详细的阐明了零件应采用何种加工方案。特别是孔和孔系，提到了现代技术中的特种加工。
最后总结了在本次设计中的收获。
关键词 注射模 哈夫分型 一模两腔
Abstract
First of all, this paper, the status quo and the development of mold and die in real life the extensive application. Second, the article detailed the Shudi Endian Injection Mould was the analysis and design.
Design on the molding machines in various parts of choice. Focused on injection mold casting system design; Injection Mould type of choice; Injection Mould side core pulling the design.
Parts of the cavity design using the Hough type, side core pulling bodies and achieve a two-cavity. Cavity also conducted a strict calculation.
Wen also expounded in detail what parts should be processing programme. In particular hole and holes, referred to the modern technology of special processing.
Finally,the paper Concluded the harvest of the design.
Keywords Injection Mould Hough type Two cavity in one block
目 录
1 引言 1
1.1 塑料模具的现代及发展 1
1.2 塑料注塑模具的设计步骤 5
1.3 课题任务要求 7
2 方案分析与设计 8
3 竖笛尾段的详细设计 10
3.1 塑料注塑成型机的选择 10
3.2 注射模具分型面的选择 13
3.3 模具结构设计 13
3.4 注射模具浇注系统的设计 14
3.5 塑料注射模具的温度调节系统设计 19
3.6 注射模具成型零件和模体的设计 19
3.7 注射模具侧抽芯机构的设计 21
3.8 注射模具的顶出机构的设计 23
4 注射模加工工艺设计 25
4.1 模具的加工 25
4.2 模板的平面加工 26
4.3 孔及孔系的加工 27
4.4 坯料确定 29
4.5 成型零件加工 29
结束语 31
致谢 32
参考文献 33
设计中介绍了成型机中各个零件的选择。着重阐述了注射模具浇注系统的设计；注射模具分型面的选择；注射模具侧抽芯机构的设计等。
对零件型腔的设计采用了哈夫分型，侧抽芯机构并做到一模两腔。还对型腔进行了严格的计算。
文中还详细的阐明了零件应采用何种加工方案。特别是孔和孔系，提到了现代技术中的特种加工。
最后总结了在本次设计中的收获。关键词 注射模 哈夫分型 一模两腔
Abstract
First of all, this paper, the status quo and the development of mold and die in real life the extensive application. Second, the article detailed the Shudi Endian Injection Mould was the analysis and design.
Design on the molding machines in various parts of choice. Focused on injection mold casting system design; Injection Mould type of choice; Injection Mould side core pulling the design.
Parts of the cavity design using the Hough type, side core pulling bodies and achieve a two-cavity. Cavity also conducted a strict calculation.
Wen also expounded in detail what parts should be processing programme. In particular hole and holes, referred to the modern technology of special processing.
Finally,the paper Concluded the harvest of the design.
Keywords Injection Mould Hough type Two cavity in one block
目 录
1 引言 1
1.1 塑料模具的现代及发展 1
1.2 塑料注塑模具的设计步骤 5
1.3 课题任务要求 7
2 方案分析与设计 8
3 竖笛尾段的详细设计 10
3.1 塑料注塑成型机的选择 10
3.2 注射模具分型面的选择 13
3.3 模具结构设计 13
3.4 注射模具浇注系统的设计 14
3.5 塑料注射模具的温度调节系统设计 19
3.6 注射模具成型零件和模体的设计 19
3.7 注射模具侧抽芯机构的设计 21
3.8 注射模具的顶出机构的设计 23
4 注射模加工工艺设计 25
4.1 模具的加工 25
4.2 模板的平面加工 26
4.3 孔及孔系的加工 27
4.4 坯料确定 29
4.5 成型零件加工 29
结束语 31
致谢 32
参考文献 33
